Kawasaki Triples WorldWide

Legendary Triple Cylinder TwoStroke Motorcycles of the 70's http://kawasakitriplesworldwide.com
It is currently Sun Aug 01, 2010 7:58 am

All times are UTC




Post new topic Reply to topic  [ 90 posts ]  Go to page 1, 2, 3, 4, 5, 6  Next
Author Message
 Post subject: H2/ZX-7 Project
PostPosted: Thu Feb 07, 2008 9:43 pm 
Offline
4th gear
User avatar

Joined: Wed Sep 15, 2004 12:34 pm
Posts: 842
Location: SLO, Ca.
Hi all. I'm glad to be back after waaay too long. My project is finally moving foreward again. H2 engine in 1990 ZX-7 chassis. I know this will horrify all the purists , but I got tired of modding the stock chassis with no real handling gains. This is the very beginning of this project. Engine is cases only. No internals in it at this point except the output shaft. I have all engine parts except for a couple small bits. Working out engine mounts(Suzi silent blocks), offset sprocket, exhaust routing, etc. etc. etc. Hope all are well. Ning-Ning-Ning!!! Any thoughts, help, criticism appreciated.

Image
Image


Last edited by MotoMikeH2 on Wed Apr 02, 2008 9:43 pm, edited 1 time in total.

Top
 Profile  
 
 Post subject:
PostPosted: Thu Feb 07, 2008 11:00 pm 
Offline
I decided to set up camp
User avatar

Joined: Tue Apr 11, 2006 9:21 pm
Posts: 2330
Location: the hills above Santa Cruz, CALIF - USA
.|..


Last edited by K_trip on Wed Jul 07, 2010 10:40 pm, edited 1 time in total.

Top
 Profile E-mail  
 
 Post subject:
PostPosted: Thu Feb 07, 2008 11:16 pm 
Offline
I Love this board!
User avatar

Joined: Thu Feb 10, 2005 1:42 am
Posts: 5364
oh lets see , that kicker looks bitchin >really like how that looks

looking at her over from the left side, engine looks almost like it belongs there :) , except for one part of her, would suggest maybe a shave of sorts on the back end of the chaincase cover :idea: after the engine is final fitted where is will stay


Top
 Profile  
 
 Post subject:
PostPosted: Thu Feb 07, 2008 11:52 pm 
Offline
4th gear
User avatar

Joined: Wed Sep 15, 2004 12:34 pm
Posts: 842
Location: SLO, Ca.
Thanks guys. The kicker is a KX500 unit. I drilled/tapped 6/1.0 in bottom and use a bolt to lock it to kick shaft. Looks like output shaft sprocket needs 1.25" offset. Think I'll need an outboard bearing support to make it happy. Pipes will be last hurdle I believe. Gonna drill my '75 H2 cases for Suzi rubbers. It's hanging from H2 stock upper rear engine mount brackets used on top and bottom rear(only for testing engine position).


Top
 Profile  
 
 Post subject:
PostPosted: Fri Feb 08, 2008 3:30 pm 
Offline
High Priest of Triples
User avatar

Joined: Thu Jul 03, 2003 2:41 am
Posts: 8237
Location: Minnesota
Quote:
I drilled/tapped 6/1.0 in bottom and use a bolt to lock it to kick shaft

That's also my "fix" for stripped out splines (OR - if you want to prevent it)on a kicker boss - you can "hide" that fix by using a 6mm allen head set screw if you don't like the bolt head sticking out/catching on anything. You just need to be sure you don't go too far into the shaft so you don't weaken it.


Top
 Profile  
 
 Post subject:
PostPosted: Sat Feb 09, 2008 9:12 pm 
Offline
2nd gear
User avatar

Joined: Wed Jun 12, 2002 7:58 pm
Posts: 181
Nice projekt!!!

Here my ZXR400 with H2 engine:
Image
Image
Image
Image

More info: http://www.zweitakte.de/projekte/ralf_zxr/zxr_h2.htm

RalfK


Top
 Profile E-mail  
 
 Post subject:
PostPosted: Sat Feb 09, 2008 11:26 pm 
Offline
4th gear
User avatar

Joined: Wed Sep 15, 2004 12:34 pm
Posts: 842
Location: SLO, Ca.
Thanks Ralf. Your bike looks great! When I get mine done we need to go for a ride!!! I need info on your front sprocket solution.


Top
 Profile  
 
 Post subject:
PostPosted: Sun Feb 10, 2008 1:06 am 
Offline
4th gear
User avatar

Joined: Wed Nov 22, 2006 3:11 pm
Posts: 918
That'll be a long ride :lol:


Top
 Profile  
 
 Post subject:
PostPosted: Sun Feb 10, 2008 2:19 am 
Offline
4th gear
User avatar

Joined: Wed Sep 15, 2004 12:34 pm
Posts: 842
Location: SLO, Ca.
Long and wet. Have to keep the front wheel up all the way over the big water!!! Do they make a 170 series rear paddle tire? he he he


Top
 Profile  
 
 Post subject:
PostPosted: Fri Mar 21, 2008 9:15 pm 
Offline
4th gear
User avatar

Joined: Wed Sep 15, 2004 12:34 pm
Posts: 842
Location: SLO, Ca.
Ok so now I have all wiring done using H2C wiring harness. I'll fab a complete harness later. H2 clutch and throttle cables modded to fit ZX7 switch housings. H2 tach in ZX7 guage cluster. Gonna try the stock tach later. I think it will work as the ZX7 uses two pickup coils each firing once per rev. My local master machinist made my offset front sprocket with nose for outboard bearing support plate. Support plate in the works now. I'm figuring the engine mounting location/ rubber mounting/ chain roller/ slipper, etc. I'm getting closer to having a ridable triple!!!

I'll post more pics soon. Gotta shrink the pics down a little.

:D :D :D


Top
 Profile  
 
 Post subject:
PostPosted: Fri Mar 21, 2008 9:40 pm 
Offline
1st gear

Joined: Wed Jul 05, 2006 2:50 am
Posts: 88
Location: Between Chicago & Milwakee
http://babelfish.altavista.com/babelfish/tr


Top
 Profile  
 
 Post subject:
PostPosted: Fri Mar 21, 2008 11:23 pm 
Offline
4th gear
User avatar

Joined: Wed Sep 15, 2004 12:34 pm
Posts: 842
Location: SLO, Ca.
?Translate?
?Que?


Top
 Profile  
 
 Post subject:
PostPosted: Sun Mar 23, 2008 6:14 pm 
Offline
4th gear
User avatar

Joined: Wed Sep 15, 2004 12:34 pm
Posts: 842
Location: SLO, Ca.
Ok so here are a few pics of the bike as it is now. Not as close to done as it may/may not look. Still need to make the outboard bearing support plates, rubber motor mounts, chain slider, and on and on but making progress. Outboard bearing on order be here in two days then I can start the carrier plates design. Pipes are just mocked up for the pics carbs not clamped(drooping center carb) :oops: but all wiring, cables hooked up and working. Clutch cable not installed in these pics. Like the rust on the pipes? I know I do! My precious FBGs bought new now LOOK theyre lighter after the rust is removed! :D :lol:

Oh btw I do have a plastic frame slider mounted under the chain off the rear side stand mount bolt which keeps the chain off (barely) the lower motor mount. Still need to rethink that area.

Any suggestions (scrap it!) appreciated

Image
Image
Image


Top
 Profile  
 
 Post subject:
PostPosted: Sun Mar 23, 2008 8:36 pm 
Offline
I Love this board!
User avatar

Joined: Thu Feb 10, 2005 1:42 am
Posts: 5364
some of the dirt bikes have chain sliders :idea:


Top
 Profile  
 
 Post subject:
PostPosted: Sun Mar 23, 2008 9:01 pm 
Offline
4th gear
User avatar

Joined: Wed Sep 15, 2004 12:34 pm
Posts: 842
Location: SLO, Ca.
Yeah I'll prolly have to make a custom strip of slider plastic(can't remember the compound they use) or get a used one off egay to play with.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 90 posts ]  Go to page 1, 2, 3, 4, 5, 6  Next

All times are UTC


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group